Civil Engineering Lab Equipment Experts
Bulk Tender
Civil Testing
Engineering Lab
Africa Exports
Materials testing is where construction risk gets priced. A ready-mix plant that cannot demonstrate 28-day strength has no defence in a dispute. A quarry that cannot certify aggregate properties loses supply approvals. A highway contractor without a functioning site laboratory cannot raise a bill.
Naugra Lab Equipments manufactures the instruments those laboratories run on. For more than 20 years we have supplied commercial testing laboratories, cement and ready-mix producers, quarry operators, precast plants, highway and infrastructure contractors, and government testing departments across 90-plus countries.
This is an overview of the six materials testing disciplines we build for, and what to consider when specifying equipment for commercial rather than research use.
Three requirements separate production testing equipment from everything else.
Throughput. A commercial lab may run dozens of cube tests a day, every day, for years. Duty cycle matters more than peak specification. Motorised units, automatic counters and digital readouts stop being conveniences and start being throughput requirements.
Traceability. If your laboratory is accredited to ISO/IEC 17025 or working toward NABL accreditation, every instrument in the measurement chain must be calibratable against traceable references. Equipment itself is not accredited — laboratories are — but equipment that cannot hold calibration or accept standard procedures will fail you at audit.
Defensibility. Test results end up in contracts, claims and occasionally litigation. Instruments built to the dimensional tolerances the standard specifies produce results that survive challenge. Approximations do not.
We build to those three requirements.
Physical and mechanical property testing to IS 4031 and equivalents: Vicat apparatus for consistency and setting time, Le Chatelier and autoclave for soundness, Blaine air permeability for fineness, and compression testing for mortar strength. Essential for cement producers, blending plants and any lab certifying incoming binder.
Los Angeles abrasion, impact value, crushing value, ten percent fines, flakiness and elongation, sieve analysis, specific gravity and soundness — the IS 2386 series. The core of quarry quality control and of any lab approving aggregate for structural or pavement use.
Fresh property testing (slump, compaction factor, air content, density) and hardened testing (compressive, flexural and split tensile strength), plus non-destructive methods for in-situ assessment. The workload of ready-mix operations, precast plants and structural investigation firms.
Triaxial, direct shear, unconfined compression, consolidation, permeability, CBR, Proctor compaction and field density. Used by geotechnical consultancies, foundation contractors and earthwork quality control.
Penetration, softening point, ductility, flash and fire point, viscosity, Marshall mix design, binder extraction and ageing. The equipment set for refineries, asphalt plants, road contractors and highway authority laboratories.
Total stations, digital and vernier theodolites, auto and digital levels, plane table sets, prismatic compasses and the full field accessory range. For setting out, as-built verification, quantity measurement, deformation monitoring and mine surveying.
Each discipline has a dedicated article on this site covering the individual instruments in detail.
We manufacture. Our own facility, our own engineering team, our own quality control. Not a trading house putting a label on someone else's product. When a load frame needs to be stiffer or a temperature controller tighter, that is a decision we can make.
Complete range. Civil, mechanical, electrical, electronics, educational, vocational and general testing equipment from one facility. An organisation running several laboratories deals with one manufacturer and one set of paperwork.
Worldwide export. More than 90 countries, with complete export documentation and established logistics. We have shipped into most regulatory environments you are likely to be operating in.
Twenty-plus years. Two decades of building instruments that live in working laboratories. That experience shows up in the components that take daily abuse — drives, bearings, load paths and controls.
Competitive pricing. Efficient Indian manufacturing, not reduced specification. The saving comes from where we produce.
Turnkey and support. Supply, installation, commissioning, operator training and after-sales support from a single partner. For a new site laboratory or a plant QC facility, we take it from empty room to first valid test result.
Can you equip a laboratory working toward NABL or ISO 17025 accreditation? Yes. Our instruments are manufactured to standard specifications and are designed to accept traceable calibration. We can advise on what an assessor will look for.
Do you supply site laboratories for project durations? Yes — we regularly supply complete site labs for highway, dam and infrastructure projects.
Can you quote against a specification document? Send us the specification or tender schedule and we will quote line by line.
Tell us what your laboratory needs to certify, and we will build a quotation around it.
Naugra Lab Equipments | naugralabequipments.com
Talk to our specialists about your laboratory setup or bulk-tender requirements.
